LC010 Projector Lens 1.5–3:1 for Optoma ZU820 ZU920 ZU800 CUL1020 CUL600 CUL700 CUL800 CUL900

The LC010 is a medium-to-long throw lens for 0.65/0.66/0.67-inch panel (Optoma) projectors, with a throw ratio of 1.5–3:1 and lens shift. It is compatible with 35 projector models across 2 model series. This article lays out the lens specifications, installation distances, model compatibility list, and replacement key points all at once.

1. Lens Specifications

Shift capability is the key differentiator of this lens. A shift range of horizontal +64%, -44% and vertical +34%, -27% means the projector can be installed off the screen's center axis and the image can be brought back via lens shift, without resorting to keystone correction. Keystone correction comes at a cost—each step of correction loses a portion of actual pixels, and text edges become soft. In installation work, anything that can be solved with shift should never be solved with keystone correction; this is the baseline for image quality.

2. Converting Throw Ratio to Installation Distance

Throw ratio is the ratio of installation distance to image width. This lens is zoom (1.5–3:1), so a given image size corresponds to a range of distances; installation anywhere within this range will achieve focus.

The above is the clear distance from the lens face to the screen, excluding rear ventilation and cabling space behind the projector body. Calculated at 16:10 aspect ratio; actual values are subject to on-site measurement and the manual.

Image quality differs at the two ends of the zoom range: toward the near end the image is brighter with slightly softer edges; toward the far end the edges are sharper with slightly reduced brightness. Where space permits, it is recommended to land in the middle of the range. After installation, first find the sharpest position on the focus ring, then fine-tune the shift—moving both variables at once makes it hard to find the sweet spot.

3. Compatible Models (35 Projectors, Optoma)

The table below is sorted by model production date from newest to oldest, including each model's resolution, brightness, and original lens zoom ratio, for quick identification based on project requirements.

The zoom ratio is the zoom factor of the model's original standard lens (upper limit of the original throw ratio range ÷ lower limit), not the zoom range of the lens described in this article.

Factory-Replaceable Lens Models

Among these models, 14 projectors can be fitted with factory lenses; the corresponding throw ratios for each model are shown in the table below, serving as a reference against factory options.

Optoma Factory Lenses

The 1.5–3:1 model in this article is closest in focal range to the factory A06 (1.22 ~ 1.52), allowing direct comparison for selection.

Common Characteristics of These Models

The original standard lens throw ratios of the 35 models are mostly concentrated at 1.22-1.52:1. The 1.5–3:1 model in this article represents an adjustment in focal range—the same projection distance can produce a different image size, which is precisely the direct reason for changing lenses; at the same time, full shift capability is retained, so the image can still be aligned after adjusting the focal range.

4. Three Things to Confirm Before Replacement

• Panel and resolution must match. This model is for 0.67-inch panels. Machines with different panel sizes or resolutions will show some differences in projection performance; it is safest to verify against the unit's nameplate before installation.
• Interface and locking structure. Interface compatibility is good within the same generation platform, but locking latch positions differ between generations. If the image is skewed or edges are soft after installation, it is most likely that the lock is not fully engaged, not a problem with the lens itself.
• Shift margin must be factored into installation. The shift range leaves room for installation, but edge image quality degrades when pushed to the limit; it is recommended to stay within 70% of the rated value in actual use.

For models not on the list, it is more reliable to send us the unit nameplate and a photo of the original lens for verification—same-generation platforms often share interfaces, but ordering based on model similarity alone is a risk not worth taking.