Projectiondesign 400-0003-00 Projector Lamp in One Table (Compatible with 16 Models)

Looking for a replacement lamp for your Projectiondesign projector? Check the model number first, then everything else. Here's a quick reference for the 400-0003-00 specifications and its 16 compatible projector models.

Specifications at a Glance

The specifications above are sourced from the Zorsika product database. Contact our sales team for the full technical datasheet.

Compatible Models: 16 Projectiondesign Projectors

The following verified compatible Projectiondesign projector models for the 400-0003-00 are listed below, separated by commas:

Action! 1, Action! 1 MKII, Action! 05, Action! 05 MKII, EVO, F1+ SXGA, F1 SXGA-6, F1 SXGA, F1 XGA, F1, F1+ XGA WIDE, F1+ XGA, evo+, cineo MK II, cineo MK III, Action! 1 MK III

Note: Projectors within the same generation often share the same lamp module. For models not listed, contact Zorsika technical support for confirmation.

Same Specs, Why Choose Zorsika PRO

For high-volume, standard lamp modules like the 400-0003-00, the Zorsika PRO series offers a replacement that matches the original specifications exactly. Power, arc gap, and reflector size are all matched item-by-item against the original, and every unit is individually tested before shipping — ready to install with no modifications needed.

• Spec-Matched: Power, arc gap, and reflector size are matched item-by-item to original parameters
• Individually Tested: Every lamp is lit and tested before leaving the factory, ensuring brightness and stability
• Warranty Commitment: 180-day warranty on lamps; non-artificial damage under normal use is covered by after-sales service
• Stable Supply: Supports bulk purchasing and project-based supply

In short: if you want original quality but with greater peace of mind overall, the Zorsika PRO series projector lamp is designed exactly for this scenario.

Note: Brightness and lifespan performance are significantly affected by projector condition, operating environment, and cooling. Zorsika does not make uniform performance claims; we recommend testing 1-2 sample units before bulk purchasing.

FAQ

Q: Why choose Zorsika PRO instead of the original?

A: The core philosophy of the Zorsika PRO series is "original parameters, our own quality control": power, arc gap, and reflector size are matched item-by-item to the original, but with an additional individual lighting test before shipping and a 180-day warranty. Compared to the original, it offers greater peace of mind overall; compared to other alternatives, quality control is more consistent.

Q: How do I choose between original packaged, original bare, and replacement lamps?

A: If you prioritize brightness stability and long-term reliability, go with the Zorsika PRO series — matched item-by-item to original parameters, individually tested before shipping, with performance comparable to the original and greater peace of mind overall, plus a 180-day warranty. For standard business, education, and conference room use, the PRO series is also the more worry-free choice. While other replacement lamps cost less, the arc tube source and quality control vary significantly, increasing the risk of brightness degradation and shortened lifespan — these are only recommended for temporary backup units.

Q: What should I do if the projector shows "lamp not recognized" after replacement?

A: First, check whether the lamp hour counter has been reset — most of these prompts are caused by a counter that hasn't been cleared. If the error persists after resetting, contact Zorsika technical support, and we'll provide the reset procedure and troubleshooting guidance for your specific model.

Q: My projector isn't in the 16-model list above. Can I still use the 400-0003-00?

A: The list covers verified models but isn't exhaustive. Projectiondesign projectors from the same generation often share lamp modules. Take a photo of the projector nameplate and the original lamp label and send it to Zorsika technical support, and we'll help confirm compatibility.

Q: Is there an installation guide for the 400-0003-00?

A: Yes. The lamp door location and removal/installation steps for these Projectiondesign models are essentially the same. Contact Zorsika sales to get illustrated or video tutorials for your specific model.

Three Things to Verify Before Purchasing

1. Check the Nameplate Model: Open the projector's lamp door and confirm the model on the lamp label matches 400-0003-00 exactly. Some Projectiondesign models have suffixes like -V or +, but the lamp module is usually interchangeable. When in doubt, take a photo of the nameplate and send it to Zorsika technical support for confirmation.
2. Confirm the Lamp Form: The same model comes in four forms — original packaged, original bare, replacement, and used — and they differ significantly. Original bare means an original arc tube with a third-party housing, which typically offers the best overall value. Be sure to specify exactly which form you want on your order to avoid disputes upon delivery.
3. Verify Physical Specifications: Reflector size 56X56D, socket E21.8, and arc gap must all match your original lamp. If any of these don't align, the lamp may not fit or may fail to light.

Things to Keep in Mind After Replacing the Lamp

• Clean Dust Regularly: Dust buildup on the air intake and air filter directly raises the lamp's operating temperature. In dusty environments, clean every 1-2 months; in normal office environments, every 3-6 months.
• Use Eco Mode: This lamp supports dual power modes of 300W / 250W. Switching to eco mode for everyday presentations significantly reduces thermal load on the lamp.
• Avoid Frequent On/Off Cycling: Thermal cycling is one of the main causes of lamp wear. If the projector won't be used for a short period, use the shutter/blank function instead of repeatedly cutting power.
• Shut Down Properly: After powering off, wait for the cooling fan to stop before unplugging. Cutting power while the lamp is hot causes rapid cooling and is a common cause of lamp rupture.
• Reset the Lamp Counter After Replacement: Be sure to reset the lamp hour counter in the menu after installing a new lamp; otherwise, the projector will continue to trigger alarms based on the old timer.

Related Resources

• Zorsika Technical Support Center
• Projector Brand & Compatible Model Lookup
• Projector Lamp / Lens / Air Filter Product Library

Sales Inquiries

For consultation on the Projectiondesign 400-0003-00, bulk pricing, or the full compatible model list, contact us through the following channels:

• Website: www.zorsika.com
• Phone: 0086-20-38551187
• Email: sales@zorsika.com
• Business Hours: Monday to Friday, 9:00-18:00

The lamp module model, specifications, and compatible model data in this article are sourced from the Zorsika product database. Data is continuously updated; final confirmation is subject to actual quotation inquiries.